Welcome Guest! The IOSH forums are a free resource to both members and non-members. Login or register to use them

Postings made by forum users are personal opinions. IOSH is not responsible for the content or accuracy of any of the information contained in forum postings. Please carefully consider any advice you receive.

Notification

Icon
Error

Options
Go to last post Go to first unread
Kay  
#1 Posted : 23 November 2012 13:58:22(UTC)
Rank: Forum user
Kay

Please can anyone advise on this? The building is a World War 2 aircraft hangar made of corrugated metal with a very thin (worn away by the elements over the last 70+ years) layer of black paint which has been identified to contain asbestos. We want to cut a personnel doorway into the building, probably using a 9" disc grinder. It would probably take less than an hour. I've looked on the HSE website but am more confused than ever regarding 1. Can we do it or do we need a licensed contractor? 2. Is it 'notifiable'? 3. What control measures would need to be in place? 4. Would our guy need special asbestos training? If anyone can give a few pointers it would be much appreciated. Many thanks Kay
Stephens25059  
#2 Posted : 23 November 2012 14:23:35(UTC)
Rank: Forum user
Stephens25059

Kay Similar type work is covered here http://www.hse.gov.uk/pubns/guidance/a26.pdf Not licensed work as the sheet says and not notifiable The trickier bit is the use of an disc cutter as this will potentially generate a lot of dust/fume that you cannot control. What about removing the paint with a gel paint stripper (not DCM based obviously) where you intend to make the cut lines - if the resulting gel paint mush is less than 0.1% asbestos then it is not hazrdous waste. Just thinking aloud.....
Chris99  
#3 Posted : 23 November 2012 14:38:16(UTC)
Rank: Forum user
Chris99

I wouldn't be quite so definite when giving advice on t'internet. That sheet is for Artex, where the material Kay is talking about sounds like Galbestos. Now, usually low risk, but it can contain substantially more asbestos than artex and anecdotally could contain Crocidolite. Kay: Be sure of what you're working on by getting the material analysed and if you'd feel happier get some advice from a consultant. It may be possible to carry it out in house, but no-one can make that judgement without seeing it. However, if you don't already have staff trained to carry out non-licenced work, I would suggest in this instance it will be cheaper & easier to employ a local licensed contractor. I would prefer a less whizzy mode of cutting (perhaps a still saw or even hydraulic snips) but we should still be talking a few hundred, rather than thousand pounds. HTH, Chris. PS And isn't the HSE 'guidance' on NNLW useful!
rodgerker  
#4 Posted : 23 November 2012 15:50:40(UTC)
Rank: Forum user
rodgerker

Not a lot of information to go on. However two comments: 1. You must not use any form of grinder for cutting the material if it contains asbestos. 2. The work would probably require notification to the HSE as "Notifiable Non-Licensed Work". Therefore a "Licensed Contractor" would not necessarily be required, but a contractor who would meet the requirements of the new CAR 2012 would. I work for an asbestos removal company not far from you, if you want to contact me we can discuss further. Rodger Ker
MEden380  
#5 Posted : 23 November 2012 16:22:03(UTC)
Rank: Super forum user
MEden380

Kay Have you considered removing whole sheets in the vicinity of your new opening and replacing with new around the edges of your door. Might be safer, quicker and prove cost effective as well.
Users browsing this topic
Guest
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.