Definition of Sloping Roofs Options  Watch this topic  Print this topic » Normal Threaded

Previous Topic Next Topic

Admin		#1 Posted : 03 March 2009 16:16:00(UTC)
Rank: Guest		Posted By Steve Holliday I have from some course notes the definition of a sloping roof as those roofs with a pitch of greater than 10 degrees. Does anyone know of any published standard from which this is derived as this is not referenced in my notes. Thnaks for any help
User Profile View All Posts by User View Thanks

Admin		#2 Posted : 03 March 2009 16:37:00(UTC)
Rank: Guest		Posted By clarkey Hi I have had a look in the Construction Skills GE 700 and it doesn't directly reference but on looking at the reference list I would hazard a guess that it is probably in INDG284 Working on roofs. Hope this helps
User Profile View All Posts by User View Thanks

Admin		#3 Posted : 03 March 2009 22:23:00(UTC)
Rank: Guest		Posted By Leslie Steve I will also have a look through my old material, however I have always treated 10 degrees or more as sloping and this was based on info read some years ago. Leslie
User Profile View All Posts by User View Thanks

Admin		#4 Posted : 04 March 2009 10:34:00(UTC)
Rank: Guest		Posted By Della Pearlman As far as I know, the minimum roof pitch for which tiles are available is 10 degrees - (there are a couple of firms making tiles at this pitch) - so that would confirm that this is the definition of a sloping roof. After that, the roof would be treated as a flat roof, with a membrane or similar covering
User Profile View All Posts by User View Thanks

Admin		#5 Posted : 04 March 2009 10:41:00(UTC)
Rank: Guest		Posted By Della Pearlman And I have found you the reference: BS 5534 2003 Code of Practice for Slating and Tiling defines a roof as "part of a building with a pitch greater than 10° and less than 75°" hope this helps Della
User Profile View All Posts by User View Thanks

Admin		#6 Posted : 04 March 2009 10:54:00(UTC)
Rank: Guest		Posted By SNS so what is a roof beyond a pitch of 75 degrees???
User Profile View All Posts by User View Thanks

Admin		#7 Posted : 04 March 2009 11:03:00(UTC)
Rank: Guest		Posted By Alan Hoskins A wall??? ;-) A
User Profile View All Posts by User View Thanks

Admin		#8 Posted : 04 March 2009 12:20:00(UTC)
Rank: Guest		Posted By Ron Hunter Discussion within the normative references of BS EN 13374:2004 (edge protection systems) confirm a 10 degree figure. As for >75 degrees, what about a "sloping facade"? :-)
User Profile View All Posts by User View Thanks

Admin		#9 Posted : 04 March 2009 12:21:00(UTC)
Rank: Guest		Posted By Alan Nicholls Cladding Alan
User Profile View All Posts by User View Thanks

Admin		#10 Posted : 04 March 2009 13:42:00(UTC)
Rank: Guest		Posted By peter gotch Steve. It derives from the Construction (Working Places) Regulations 1966. Regulation 35 defined a sloping roof as one having a pitch of more than 10 degrees. Requirements for protection were stronger where the pitch was more than 30 degrees or where the pitch was less, but with a surface liable to beome slippery. Revoked in 1996. Regards, Peter
User Profile View All Posts by User View Thanks

Admin		#11 Posted : 04 March 2009 14:21:00(UTC)
Rank: Guest		Posted By Steve Holliday Thanks to everyone who has responded. i have looked up all the references mentioned and also found 10 degrees quoted in HS(G)33.
User Profile View All Posts by User View Thanks

Admin		#12 Posted : 04 March 2009 16:42:00(UTC)
Rank: Guest		Posted By Ron Hunter I looked, but couldn't see it in HSG 33. Could you give me a page/section number? Is the new HSG 33 out there yet?
User Profile View All Posts by User View Thanks

Users browsing this topic

Guest (3)